SpecPoxy Sealer

SpecPoxy Sealer

SpecPoxy Sealer is a high-solids, two-component, low viscosity penetrating epoxy sealer designed to protect both new and existing concrete against deicing salts and chemical attack. It penetrates concrete pores to form a sub-surface seal that resists the penetration of liquids, chloride ions, and chemicals. Additionally, its low viscosity makes it an excellent solution for healing and sealing deteriorated concrete surfaces.

  • Easy 1 to 1 mix ratio
  • Penetrates concrete to seal against liquid absorption
  • Offers excellent resistance to a variety of chemicals
  • Cures to an amber color
  • Easy to apply by brush, roller, squeegee, or sprayer
  • Structurally restores concrete surfaces

Coverage

  • Coverage rate is approximately 100 sq-ft per gallon for broom –finished concrete
  • Apply @ a minimum 500 sq-ft/gallon on steel-troweled surfaces.
  • Coverage rate depends on the porosity of the concrete. Avoid coatings in excess of 3 mils to prevent solvent encapsulation (soft, uncured film)

Packaging

  • 2 gallon units
  • 10 gallon units
  • 110 gallon units

Shelf Life

Store SpecPoxy Sealer in its original containers and keep tightly closed. Do not allow the accumulation of water, dirt or other contaminants. The shelf life of properly stored SpecPoxy Sealer is two years from date of manufacture.

Standards

  • SpecPoxy Sealer is certified for use by the USDA for use in federally inspected meat and poultry plants
  • Available with a fluorescent dye to comply with DOT requirements.

Surface Preparation:

  • New concrete must be a minimum of 21-28 days old with all curing compounds and sealers removed.
  • Concrete must be clean, dry, and sound. Remove all oil, dirt, debris, paint, and unsound concrete.
  • For hard troweled surfaces, a test section is recommended to determine if additional surface profiling (such as shotblasting or etching) is required.

Mixing:

  • Condition materials to a temperature of 55°F to 80°F.
  • Mix Parts A and B separately for one minute using a drill and mixing prop, then mix together for 3 minutes to ensure a proper chemical reaction.

Placement:

  • Apply by squeegee, roller, or industrial sprayer.
  • For sealing hairline cracks, flood coat the surface and let the material pool over cracked areas for 5 minutes to ensure the cracks are filled.
  • Squeegee or broom away any excess material from the surface.
  • For improved skid-resistance, broadcast clean dry silica sand immediately after excess sealer has been removed. After initial cure, remove excess sand.
Total Solids Content 70%
Color Clear amber
Mixed Viscosity 60 cps
Pot Life @ 70°F, 2 Gallon Volume 35 minutes
Thin Film Dry Time @ 70°F < 4 hours
% Elongation
ASTM D638		 38%
Data Sheets

Download Technical Data Sheet

Download Safety Data Sheet

Download Technical Data Sheet (Spanish)

Coverage

  • Coverage rate is approximately 100 sq-ft per gallon for broom –finished concrete
  • Apply @ a minimum 500 sq-ft/gallon on steel-troweled surfaces.
  • Coverage rate depends on the porosity of the concrete. Avoid coatings in excess of 3 mils to prevent solvent encapsulation (soft, uncured film)

Packaging

  • 2 gallon units
  • 10 gallon units
  • 110 gallon units

Shelf Life

Store SpecPoxy Sealer in its original containers and keep tightly closed. Do not allow the accumulation of water, dirt or other contaminants. The shelf life of properly stored SpecPoxy Sealer is two years from date of manufacture.

Standards

  • SpecPoxy Sealer is certified for use by the USDA for use in federally inspected meat and poultry plants
  • Available with a fluorescent dye to comply with DOT requirements.

Surface Preparation:

  • New concrete must be a minimum of 21-28 days old with all curing compounds and sealers removed.
  • Concrete must be clean, dry, and sound. Remove all oil, dirt, debris, paint, and unsound concrete.
  • For hard troweled surfaces, a test section is recommended to determine if additional surface profiling (such as shotblasting or etching) is required.

Mixing:

  • Condition materials to a temperature of 55°F to 80°F.
  • Mix Parts A and B separately for one minute using a drill and mixing prop, then mix together for 3 minutes to ensure a proper chemical reaction.

Placement:

  • Apply by squeegee, roller, or industrial sprayer.
  • For sealing hairline cracks, flood coat the surface and let the material pool over cracked areas for 5 minutes to ensure the cracks are filled.
  • Squeegee or broom away any excess material from the surface.
  • For improved skid-resistance, broadcast clean dry silica sand immediately after excess sealer has been removed. After initial cure, remove excess sand.
Total Solids Content 70%
Color Clear amber
Mixed Viscosity 60 cps
Pot Life @ 70°F, 2 Gallon Volume 35 minutes
Thin Film Dry Time @ 70°F < 4 hours
% Elongation
ASTM D638		 38%
Data Sheets

Download Technical Data Sheet

Download Safety Data Sheet

Download Technical Data Sheet (Spanish)